UMG 104, with a 500 MHz DSP (digital signal processor), is a fully fast and powerful network analyzer. The continuous analysis of the 8 channels with 20 kHz per channel allows the recording of the electrical parameters (more than 800 values), minimum and maximum values, the essential voltage quality values as harmonics (up to 40, each phase with the recognition of the address). On the basis of data that production failures can be avoided, concepts can be developed for example to reduce energy costs, the measures taken and with the UMG 104 the achieved improvements can be monitored and documented. Through modern communication architectures the recorded data is sent to a central location, centrally stored in efficient databases and available for further processing in an open architecture. The easy connection of an available building control system or SPS environment extends the areas of use of the UMG 104.

Control center and energy manager via Ethernet, including Energy Meter.

Three-phase bidirectional meter.
Nominal voltage 230 V/400 V
Frequency 50 Hz/±5 %.
Nominal/limit current per phase conductor 5 A/63 A (>63 A combined with external current transformers)
Starting current <25 mA
Connection cross-section From 10 mm² to 16 mm² 1) (for 63 A protection)

medida Indirecta.

A power meter transmits the measured amount of power to the SolarLog for analysis. It serves as a consumption meter, showing a comparison of produced and consumed power. It can be configured to operate with the SolarLog in three different modes:
- Measuring energy consumption for optimal utilization of the power generated.
- Measuring the total amount of energy that has been fed into the grid.
- Measuring the energy production of inverters that are not directly managed by SolarLog.

Three-phase Sigen Power Sensor CT600-DH
Sigen Power Sensor integrates seamlessly with Sigenergy devices, with no configuration required.
This power sensor is part of SigenStor's 5-in-1 energy storage system.
Sigenergy's ESS seamlessly integrates the PV inverter, battery power conversion system (PCS), EV DC charger for electric vehicles, battery pack and energy management system (EMS).

Smart Meter TS 65A-3; for recording energy consumption, three-phase, direct metering

Fronius Smart Meter TS 5KA Three Phase is a calibrated device to measure and control the amount of energy passing through the house.
It requires toroidal sensors to carry out an indirect measurement of the current passing through each of the 3 phases.

UPM209 is an innovative power meter for measuring and recording electrical parameters. It is particularly suitable for consumption analysis and control, with an excellent quality/price ratio.
UPM209 is the ideal power meter for establishing measurement points in the plant.
Compatible with Huawei's Smartlogger
6A__85...265VAC
RS485, Signbit__Basic, 1MB
kVAh L/C

Power Meter, DTSU666-HW/YDS60-80
Direct reading up to 80A
Supports indirect reading with CT x/5A (not included)

Modbus 3-phase current meter

Modular electric energy meter that displays power (kWh, kVArh and kVA) and other measurements directly on its backlit LCD display.
It is designed for three-phase load metering with connection via CT and is suitable for applications up to 12000 A.

The Victron EM24 Ethernet is a standard device for measuring the power and energy of a three-phase application, for example in the distribution box or for measuring the output of a PV inverter, an AC generator or an inverter or inverter/charger.

Sigen Power Sensor Trifásico

Huawei Smart Power Sensor DTSU666-H (3-Ph).
Valid if cable section doesn't exceeds 95 mm2 and there's not a higher intensity of 250 A.

Solis-3P-Meter-CT*3 (indirect measurement)

Preconfigured and ready to communicate with all three-phase Solis inverters
Indirect measurement wattmeter, installation without the need to modify the customer's installation
DIN35 rail mounting
LCD screen for real-time display of measurements
Open-core toroids included with measurement capacity per phase of up to 150A and 5 meters of cable
Includes 10m RS485 cable with connector for Solis inverters as standard
Ability to use other toroids with a 5 amp secondary simply by setting the transformation ratio

Features:

Indirect measurement wattmeter, installation without the need to modify the customer's installation.
DIN35 rail mounting
LCD display for real time display of measurements
10m RS485 cable with Solis inverter connector included as standard.
Ability to use other toroidals with secondary at 5 amps simply by setting the transformation ratio

Sigen Power Sensor Single Phase DH

AC current meter